Hydraulic seals manufacturer and supplier right now in 2024: The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film. Read extra details on spring seals.
Mechanical seals are engineered for most pumps, mixer and agitator applications in maintenance. In many cases the designs have been proven to be workhorses over years of use. In others seals must be designed for evolving industrial demands. The basic rotating face mechanical seal design is adaptable to serve a wide range of sealing applications including compressors. Standard mechanical seals can suit most requirements to temperatures of 500 degrees F and shaft speeds to 3600 RPM. The selection of secondary seal type often determines the temperature and chemical capabilities of the seal. The combination of materials used in the rotating and stationary faces define the abrasive resistance, and chemical resistance. Seal face combinations will also determine the amount of energy consumed by the pump, mixer, agitator or compressor. Seal faces can be balanced to permit higher pressure sealing. Balanced seals can seal pressures above 200 psi, or used in a multiple stages for higher pressures or especially severe fluid services. Special mechanical seals can be furnished to meet the most demanding of industrial applications considering pressure, temperature, speed or fluid.
Key points of engineering mechanical seal design: Select a reasonable sealing scheme, focusing on the above requirements. First of all, the dustproof performance must be good. More than 80% of the failures of the hydraulic system are directly or indirectly derived from the stains in the system. Choose the best seals For seals of the same structure, the product quality of each company varies greatly. On the whole, the quality of large foreign seal companies is relatively stable, but the probability of encountering fakes is too high. Sometimes the so-called direct supply is not reliable. In terms of domestic seals, most of them are not very good, but at present, some manufacturers’ products have been chasing or even surpassing imported products, with stable and reliable quality, such as tetrafluoroethylene and rubber seals produced by Damson Sealing.
It is ideal for single-acting sealing of reciprocating piston rods or pistons with a wide operating pressure range of up to 20 MPa. The operating temperature range is also wide from -200°C to + 250°C. It has a diameters range from 3 mm to 1600 mm and a working speed of 5 m/s. The seal has a low coefficient of friction and the friction between the contact faces is minimal among all seal types. Moreover, the contact pressure between the mating surfaces is low. It can work without lubrication and is very wear resistant. And it has a long service life.
It can maintain stable performance after prolonged exposure to various corrosive compounds. Due to its lack of polarity, low unsaturation, and high chemical stability, our gasket has high resistance to various polar chemicals such as alcohols, acids (acetic acid, hydrochloric acid, etc.), strong base (sodium hydroxide, oxidant, hydrogen peroxide), detergents, animal and vegetable oils, ketones and certain esters. It is designed to have excellent aging resistance and excellent resistance to compression set and compression stress relaxation. Therefore, our gasket has significant advantages over other conventional gaskets. Its excellent materials and manufacturing process enables it to achieve effective sealing when exposed to corrosive chemicals, friction, high temperatures or very low temperatures. At the same time, it is easy to install and has industry-leading creep resistance, which saves users a lot of time and cost and increases productivity.
Wiper seals are utilized to remove contaminants like moisture, soil, and dust. Some wipers or even scrapers possess a secondary lip utilized to catch any oil which might have bypassed the major seal. The secondary lip can also get rid of any bonded contaminate in the pole surface. These kinds of wipers are usually called double-edged wipers. Metallic scrapers could be used for sub zero temperature software and especially arduous software where foreign substances can deposit the pole.
The selection principle of the gasket: according to the working pressure, working temperature, the corrosiveness of the sealing medium and the form of the sealing surface. Temperature influence: In normal temperature and low pressure, use non-metallic soft honey gasket; in medium pressure and high temperature, choose metal and non-metal combination gasket or metal gasket; when temperature and pressure fluctuate greatly, choose good elasticity or self-tightening type Gaskets; in low temperature, corrosive media or vacuum conditions, gaskets with special properties should be considered.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. See additional information at https://www.dmsseals.com/.
DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad.